Using APIPA to configure the IP address; Using ARP to configure the IP address; Windows® systems- Page 129

Brother HL-2170W Network User's Guide

Table of Contents

NETWORK USER'S GUIDE
background image

Appendix A

122

A

Using APIPA to configure the IP address

A

The Brother print server supports the Automatic Private IP Addressing (APIPA) protocol. With APIPA, clients 
automatically configure an IP address and subnet mask when a DHCP server is not available. The device 
chooses it's own IP address in the range 169.254.1.0 through to 169.254.254.255. The subnet mask is 
automatically set to 255.255.0.0 and the gateway address is set to 0.0.0.0.
By default, the APIPA protocol is enabled. If you want to disable the APIPA protocol, you can disable it using 
the BRAdmin applications or Web Based Management (web browser). For more information, see 

Changing 

the print server settings

 on page 12

If the APIPA protocol is disabled, the IP address of a Brother print server is 192.0.0.192. However, you can 
easily change this IP address number to match with the IP address details of your network.

Using ARP to configure the IP address

A

If you are unable to use the BRAdmin applications and your network does not use a DHCP server, you can 
also use the ARP command. The ARP command is available on Windows

®

 systems that have TCP/IP 

installed as well as UNIX

®

 systems. To use arp enter the following command at the command prompt:

arp -s ipaddress ethernetaddress

ping ipaddress

Where 

ethernetaddress

 is the Ethernet address (MAC address) of the print server and 

ipaddress

 is the 

IP address of the print server. For example:

Windows

®

 systems

A

Windows

®

 systems require the dash “-” character between each digit of the Ethernet address.

arp -s 192.168.1.2 00-80-77-31-01-07

ping 192.168.1.2

UNIX

®

/Linux systems

A

Typically, UNIX

®

 and Linux systems require the colon “:” character between each digit of the Ethernet 

address.

arp -s 192.168.1.2 00:80:77:31:01:07

ping 192.168.1.2

Note

You must be on the same Ethernet segment (that is, there cannot be a router between the print server and 
operating system) to use the arp -s command.
If there is a router, you may use BOOTP or other methods described in this chapter to enter the IP address. 
If your administrator has configured the system to deliver IP addresses using BOOTP, DHCP or RARP 
your Brother print server can receive an IP address from any one of these IP address allocation systems. 
In which case, you will not need to use the ARP command. The ARP command only works once. For 
security reasons, once you have successfully configured the IP address of a Brother print server using the 
ARP command, you cannot use the ARP command again to change the address. The print server will 

Detailed Information for Brother HL-2170W Network User's Guide

Lists of information found in Brother HL-2170W Network User's Guide - Page 129

  • 69.254.
  • 1.0 through to 169.
  • 54.254.
  • 55. The subnet mask is automatically set to 255.
  • 55.0.
  • 12. If the APIPA protocol is disabled, the IP address of a Brother print server is 192.
  • 92. However, you can easily change this IP address number to match with the IP address details of your network.
  • 92.168.
  • 1.2 00-80-77-31-01-07 ping 192.
  • 68.1.
  • 92.168.
  • 1.2 00:80:77:31:01:07 ping 192.
  • 68.1.

Related Documents for Brother HL-2170W Network User's Guide