Crown LPS-800 User Manual

Sensitivity

Frequency Response

Damping Factor

2014 Dodge Charger SRT Owner Manual

Table of Contents

background image

LPS SERIES

T

T

he LPS Series of power amplifi ers from 
Crown

®

 represents a new era in afford-

able, quality power amplifi cation. All three 

models in the series are powerful, rugged and 
reliable. They are suited for applications such as 
churches, concert tours, stages, disco, pubs, or 
any place that requires amplifi er installation. 

The three models in the series are the LPS-
800, LPS-1500 and LPS-2500. They are identi-
cal except for output power.

Features include XLR inputs, Speakon

®

 and 

binding post outputs, stereo/parallel/bridge-
mono mode, power/fault/signal presence/clip 
indicators, forced-air cooling; and protection 
against shorts, no-load, on/off thumps and 
radio-frequency interference. Every LPS Series 
amplifi er is backed by a one-year limited war-
ranty.

With over six decades of experience designing 
and building rock-solid products, Crown is the 
standard in amplifi er technology. So check out 
the affordable Crown LPS Series. They are a 
powerful argument for quality and value!

For more details about the LPS Series, contact 
your authorized Crown distributor.

Specifi cations

The following applies to units in Stereo mode with 8-ohm loads 
unless otherwise specifi ed.

Performance

Sensitivity 

(for full rated power at 4 ohms)

1.25 V rms.

Frequency Response 

(at 1 watt): 40 Hz - 20 

kHz, +0/–3 dB.

Signal-to-Noise Ratio

 (below rated power, 20 

Hz to 20 kHz, A-weighted): >100 dB.

Total Harmonic Distortion (THD): 

< 0.5%, 20 

Hz - 20 kHz.

Intermodulation Distortion (IMD)

(60 Hz and 7 kHz at 4:1 from full rated output to 
–30 dB): < 0.3%.

Damping Factor 

(8 ohms, 10 Hz - 400 Hz): 

>300.

Crosstalk 

(below rated power)

:

at 1 kHz:  –76 dB.
at 20 kHz:  –58 dB. 

Input Impedance 

(nominal)

20 kilohms bal-

anced, 10 kilohms unbalanced.

Output Power:

 See power charts.

Load Impedance:

 (Note: safe with all loads).

4 ohms in stereo mode, 8 ohms in bridge-mono 
mode.

AC Line Voltage and Frequency Confi gurations 
Available 

(±10%): 120VAC/60Hz, 

220VAC/50Hz, 240VAC/50Hz.

Front Panel Controls and Indicators

Fault Indicator:

 Red LED, one per channel , 

indicates channel shutdown.

Clip Indicator:

 Red LED, one per channel, 

fl ashes when signal is audibly distorting.

Signal Presence Indicator:

 Green LED, one 

per channel, fl ashes when input signal exceeds 
–40 dBu.

Power Switch:

 Push-on, push-off.

Power Indicator:

 Blue LED illuminates when 

amplifi er is on.

Volume Control:

 Sets output level of each 

channel.

Back Panel Controls and Connectors

Reset Button:

 Resets the circuit breaker.

Output Connectors:

 One Speakon

®

 per channel 

connects to loudspeakers. One pair of binding 
posts per channel connects to loudspeakers; 
accepts banana plugs or bare wire. (European 
models do not accept banana plugs.)

Input Connectors:

 Balanced XLR, one per 

channel.

Output Mode Switch:

 Stereo (dual), Parallel or 

Bridge.

L P S   S E R I E S

• Stereo/parallel/bridge-mono 

mode

•  Effi cient forced-air cooling prevents exces-

sive thermal buildup

•  Electronically balanced XLR inputs; binding 

post and Speakon

®

 outputs

•  Two level controls, power switch, power 

LED, and six LEDs which indicate signal 
presence, clip and fault for each channel

•  Protection against shorts, no-load, on/off 

thumps and radio-frequency interference

Features

1 kHz 
Power

300W

4-ohm Stereo (per channel)

LPS-800

*1 kHz Power: refers to guaranteed minimum power
 in watts at 1 kHz with 0.5% THD.

*

8-ohm Bridge-Mono

 

600W

8-ohm Stereo (per channel)

150W

1 kHz 
Power

400W

4-ohm Stereo (per channel)

LPS-1500

*1 kHz Power: refers to guaranteed minimum power
 in watts at 1 kHz with 0.5% THD.

*

8-ohm Bridge-Mono

 

800W

8-ohm Stereo (per channel)

250W

1 kHz 
Power

725W

4-ohm Stereo (per channel)

LPS-2500

*1 kHz Power: refers to guaranteed minimum power
 in watts at 1 kHz with 0.5% THD.

*

8-ohm Bridge-Mono

 

1,450W

8-ohm Stereo (per channel)

550W

Power Charts

Detailed Information for Crown LPS-800 User Manual

Lists of information found in Crown LPS-800 User Manual - Page 1

  • 1.25 V rms.
  • Stereo/parallel/bridge-mono mode • Effi cient forced-air cooling prevents exces- sive thermal buildup • Electronically balanced XLR inputs; binding post and Speakon ® outputs • Two level controls, power switch, power LED, and six LEDs which indicate signal presence, clip and fault for each channel • Protection against shorts, no-load, on/off thumps and radio-frequency interference Features 1 kHz Power 300W 4-ohm Stereo (per channel) LPS-800 *1 kHz Power: refers to guaranteed minimum power in watts at 1 kHz with 0.

Related Documents for Crown LPS-800 User Manual