[2] LUBRICATING SYSTEM; [3] COOLING SYSTEM; Engine Oil Pressure- Page 161

Kubota L3560 Owners Manual

2014 Dodge Charger SRT Owner Manual

Table of Contents

L3560,L4060,L4760,L5060,L5460,L6060
9 ELECTRICAL SYSTEM
background image

ENGINE

L3560, L4060, L4760, L5060, L5460, L6060, WSM

1-S14

[2] LUBRICATING SYSTEM

Engine Oil Pressure

1. Remove the engine oil pressure switch, and set the oil pressure

tester (Code No. : 07916-32032). (Adaptor screw : PT 1/8)

2. Operate the engine for warming-up.

3. Measure the oil pressure at the idle speed and rated speed.

4. If the oil pressure is less than the allowable limit, do a check

below.

• Engine oil level

• Oil pump

• Oil strainer

• Oil filter cartridge

• Oil passage

• Oil clearance

• Relief valve

(When reassembling)

• After you examine the oil pressure of the engine, tighten its oil

pressure switch to the specified torque.

9Y1210824ENS0006US0

[3] COOLING SYSTEM

Fan Belt Tension

1. Push  the  belt  halfway  between  the  fan  drive  pulley  and

alternator  pulley  at  a  specified  force  98  N  (10  kgf,  22  lbf)  to

measure the deflection 

(A)

.

2. If the measurement is out of the factory specifications, loosen

the alternator mounting screws and adjust its position.

9Y1210824ENS0007US0

Engine oil pressure

At idle 

speed

Factory 

specifica-

tion

More than

98 kPa

1.0 kgf/cm

2

14 psi

Allowable 

limit

50 kPa

0.5 kgf/cm

2

7 psi

At rated 

speed

Factory 

specifica-

tion

300 to 440 kPa

3.0 to 4.5 kgf/cm

2

43 to 64 psi

Allowable 

limit

250 kPa

2.5 kgf/cm

2

36 psi

Tightening torque

Oil pressure switch

15 to 19 N·m

1.5 to 2.0 kgf·m

11 to 14 lbf·ft

Deflection 

(A)

Factory specification

7.0 to 9.0 mm

0.28 to 0.35 in.

(A) Deflection

KiSC issued 03, 2016 A

Detailed Information for Kubota L3560 Owners Manual

Lists of information found in Kubota L3560 Owners Manual - Page 161

  • 1. Remove the engine oil pressure switch, and set the oil pressure tester (Code No.
  • 2. Operate the engine for warming-up.
  • 3. Measure the oil pressure at the idle speed and rated speed.
  • 4. If the oil pressure is less than the allowable limit, do a check below.
  • 1. Push the belt halfway between the fan drive pulley and alternator pulley at a specified force 98 N (10 kgf, 22 lbf) to measure the deflection (A) .
  • 2. If the measurement is out of the factory specifications, loosen the alternator mounting screws and adjust its position.
  • 1.0 kgf/cm 2 14 psi Allowable limit 50 kPa 0.
  • 3.0 to 4.
  • 2.5 kgf/cm 2 36 psi Tightening torque Oil pressure switch 15 to 19 N·m 1.
  • 2.0 kgf·m 11 to 14 lbf·ft Deflection (A) Factory specification 7.
  • 9.0 mm 0.
  • Engine oil level • Oil pump • Oil strainer • Oil filter cartridge • Oil passage • Oil clearance • Relief valve (When reassembling) • After you examine the oil pressure of the engine, tighten its oil pressure switch to the specified torque.

Related Documents for Kubota L3560 Owners Manual