7. SERVICING; [1] MANUAL TRANSMISSION; (1) Bearing, Gear and Shaft- Page 442

Kubota L3560 Owners Manual

2014 Dodge Charger SRT Owner Manual

Table of Contents

L3560,L4060,L4760,L5060,L5460,L6060
9 ELECTRICAL SYSTEM
background image

TRANSMISSION

L3560, L4060, L4760, L5060, L5460, L6060, WSM

3-S123

7. SERVICING

[1] MANUAL TRANSMISSION

(1)  Bearing, Gear and Shaft

Checking Bearing

1. Hold  the  inner  race,  and  push  and  pull  the  outer  race  in  all

directions to check for wear and roughness.

2. Apply transmission fluid to the bearing, and hold the inner race.

Then turn the outer race to check rotation.

3. If there is any problem, replace it.

9Y1210824TRS0127US0

Clearance between Gear and Spline

1. Secure the gear with a vise.

2. Set a dial indicator (lever type) with its finger on the spline.

3. Move the shaft to measure the clearance.

4. If the clearance exceeds the allowable limit, replace them.

9Y1210824TRS0128US0

Clearance between Shift Fork and Shift Gear Groove

1. Place for in the groove to check clearance with feeler gauge.

2. If the clearance exceeds allowable limit, replace.

9Y1210824TRS0129US0

Clearance between Gear and Shaft

1. Measure the shaft O.D. (rubbing surface).

2. Measure the gear I.D. (rubbing surface).

3. Measure the O.D. of the two needles installed diagonally in the

needle bearing.

4. Calculate the clearance

(Clearance = Gear I.D. – {(2 × needle O.D.) + shaft O.D.})

5. If the clearance exceeds the allowable limit, replace them.

9Y1210824TRS0130US0

Clearance between gear 

and spline

Factory specification

0.030 to 0.078 mm

0.0012 to 0.0030 in.

Allowable limit

0.2 mm

0.008 in.

Clearance between shift 

fork and shift gear 

groove

Factory specification

0.20 to 0.40 mm

0.0079 to 0.015 in.

Allowable limit

0.8 mm

0.03 in.

Clearance between gear 

and shaft

Factory specification

0.021 to 0.054 mm

0.00083 to 0.0021 in.

Allowable limit

0.1 mm

0.004 in.

KiSC issued 03, 2016 A

Detailed Information for Kubota L3560 Owners Manual

Lists of information found in Kubota L3560 Owners Manual - Page 442

  • 7. SERVICING [1] MANUAL TRANSMISSION (1) Bearing, Gear and Shaft Checking Bearing 1.
  • 2. Apply transmission fluid to the bearing, and hold the inner race.
  • 3. If there is any problem, replace it.
  • 1. Secure the gear with a vise.
  • 2. Set a dial indicator (lever type) with its finger on the spline.
  • 3. Move the shaft to measure the clearance.
  • 4. If the clearance exceeds the allowable limit, replace them.
  • 1. Place for in the groove to check clearance with feeler gauge.
  • 2. If the clearance exceeds allowable limit, replace.
  • 1. Measure the shaft O.
  • 2. Measure the gear I.
  • 3. Measure the O.
  • 4. Calculate the clearance (Clearance = Gear I.
  • 5. If the clearance exceeds the allowable limit, replace them.

Related Documents for Kubota L3560 Owners Manual