Driving Your Mazda- Page 212

2014 Mazda MX-5 Miata PRHT Mx 5 Owners Manual

Model Year
2014 Dodge Charger SRT Owner Manual

Table of Contents

9. Customer Information and Reporting Safety Defects
background image

Black plate (212,1)

5. Press and hold the just-trained

HomeLink button and observe the
indicator light.

If the indicator light

stays on constantly,

programming is complete

and your

device should activate when the
HomeLink button is pressed and released.

NOTE

To program the remaining two HomeLink
buttons, begin with

Programming

”―

step 2.

Do not repeat step 1.

If the indicator light blinks

rapidly for

two seconds and then turns to a
constant light, continue with

Programming

steps 6

8

to complete

the programming of a rolling code
equipped device (most commonly a
garage door opener).

6. At the garage door opener receiver

(motor-head unit) in the garage, locate
the

learn

or

smart

button. This can

usually be found where the hanging
antenna wire is attached to the motor-
head unit.

7. Firmly press and release the

learn

or

smart

button. (The name and color of

the button may vary by manufacturer.)

NOTE

There are 30 seconds in which to initiate step
8.

8. Return to the vehicle and firmly

press,

hold for two seconds and release

the

programmed HomeLink button. Repeat
the

press/hold/release

sequence a

second time, and, depending on the
brand of the garage door opener (or
other rolling code equipped device),
repeat this sequence a third time to
complete the programming process.

HomeLink should now activate your
rolling code equipped device.

NOTE

To program the remaining two HomeLink
buttons, begin with

Programming

”―

step 2.

Do not repeat step 1.

For questions or comments, please contact
HomeLink at

www.homelink.com

or

1-

800-355-3515.

Gate operator/Canadian Programming

Canadian radio-frequency laws require
transmitter signals to

time-out

(or quit)

after several seconds of transmission

which may not be long enough for
HomeLink to pick up the signal during
programming. Similar to this Canadian
law, some U.S. gate operators are
designed to

time-out

in the same

manner.

If you live in Canada or you are having
difficulties programming a gate operator
by using the

Programming

procedures

(regardless of where you live),

replace

Programming HomeLink

step 3

with

the following:

NOTE

If programming a garage door opener or gate
operator, it is advised to unplug the device
during the

cycling

process to prevent

possible overheating.

Continue to press and hold the HomeLink
button while you

press and release

every two seconds

(

cycle

) your hand-

held transmitter until the frequency signal
has successfully been accepted by
HomeLink. (The indicator light will flash
slowly and then rapidly.) Proceed with

Programming

step 4 to complete.

5-68

Driving Your Mazda

Switches and Controls

MX-5_8DG6-EA-13F_Edition3 Page212
Monday, December 16 2013 2:11 PM

Form No.8DG6-EA-13F

Detailed Information for 2014 Mazda MX-5 Miata PRHT Mx 5 Owners Manual

Lists of information found in 2014 Mazda MX-5 Miata PRHT Mx 5 Owners Manual - Page 212

  • 5. Press and hold the just-trained HomeLink button and observe the indicator light.
  • 2. Do not repeat step 1.
  • 6. At the garage door opener receiver (motor-head unit) in the garage, locate the “ learn ” or “ smart ” button.
  • 7. Firmly press and release the “ learn ” or “ smart ” button.
  • 8. 8.
  • 2. Do not repeat step 1.
  • 15. Gate operator/Canadian Programming Canadian radio-frequency laws require transmitter signals to “ time-out ” (or quit) after several seconds of transmission ― which may not be long enough for HomeLink to pick up the signal during programming.

Related Documents for 2014 Mazda MX-5 Miata PRHT Mx 5 Owners Manual