FCC ID: NZLOBIHL3- Page 271

2015 Mazda CX-9 Cx 9 Owners Manual

Model Year
2014 Dodge Charger SRT Owner Manual

Table of Contents

2. Essential Safety Equipment
6. Interior Comfort
9. Customer Information and Reporting Safety Defects
background image

Black plate (271,1)

NOTE

FCC ID: NZLOBIHL3
CANADA:4112A-OBIHL3
This device complies with FCC rules part 15.
Operation is subject to the following
conditions:
1- This device may not cause any harmful
interference and
2- This device must accept any interference
that may be received including interference
that may cause undesired operation.

NOTE

The programming will not be erased even if
the battery is disconnected.

Pre-programming the HomeLink
System

NOTE

It is recommended that a new battery be
placed in the hand-held transmitter of the
device being programmed to HomeLink for
quicker training and accurate transmission of
the radio-frequency signal.

l

Verify that there is a remote control
transmitter available for the device you
would like to program.

l

Disconnect the power to the device.

Programming the HomeLink System

CAUTION

When programming a garage door
opener or a gate, disconnect the
power to these devices before
performing programming, as
continuous operation of the devices
could damage the motor.

The HomeLink system provides 3 buttons
which can be individually selected and
programmed using the transmitters for
current, on-market devices as follows:

1. Press and hold the two outer

HomeLink buttons (buttons one and
three)

releasing only when the

indicator light begins to flash (after 20
seconds).

Do not

hold the buttons for

longer than 30 seconds and

do not

repeat step 1

to program a second and/

or third hand-held transmitter to the
remaining two HomeLink buttons.

2. Position the end of your hand-held

transmitter 2.5

7.5 cm (1

3 inches)

away from the HomeLink button you
wish to program while keeping the
indicator light in view.

3. Simultaneously press and hold both the

chosen HomeLink and hand-held
transmitter buttons.

Do not release the

buttons until step 4 has been
completed.

NOTE

Some gate operators and garage door openers
may require you to replace this Programming
Step 3 with procedures noted in the

Gate

Operator/Canadian Programming

section.

4. After the HomeLink indicator light

changes from a slow to a rapidly
blinking light, release both the
HomeLink and hand-held transmitter
buttons.

NOTE

If the HomeLink indicator light does not
change to a rapidly blinking light, contact
HomeLink at

www.homelink.com

or call

1-

800-355-3515

for assistance.

Driving Your Mazda

Switches and Controls

5-93

CX-9_8DU1-EA-14H_Edition4 Page271
Thursday, June 18 2015 3:40 PM

Form No.8DU1-EA-14H

Detailed Information for 2015 Mazda CX-9 Cx 9 Owners Manual

Lists of information found in 2015 Mazda CX-9 Cx 9 Owners Manual - Page 271

  • 15. Operation is subject to the following conditions: 1- This device may not cause any harmful interference and 2- This device must accept any interference that may be received including interference that may cause undesired operation.
  • 1. Press and hold the two outer HomeLink buttons (buttons one and three) ― releasing only when the indicator light begins to flash (after 20 seconds).
  • 2. Position the end of your hand-held transmitter 2.
  • 7.5 cm (1 ― 3 inches) away from the HomeLink button you wish to program while keeping the indicator light in view.
  • 3. Simultaneously press and hold both the chosen HomeLink and hand-held transmitter buttons.
  • 4. After the HomeLink indicator light changes from a slow to a rapidly blinking light, release both the HomeLink and hand-held transmitter buttons.

Related Documents for 2015 Mazda CX-9 Cx 9 Owners Manual