Authorized Mazda Dealer.- Page 471

2015 Mazda Mazda6 Owners Manual

Model Year
2014 Dodge Charger SRT Owner Manual

Table of Contents

4. When Driving
8. Customer Information and Reporting Safety Defects
background image

Black plate (471,1)

WARNING

Attach the speed restriction sticker in a
place where it can be viewed easily by
the driver:

Ø

Applying the speed restriction
sticker to the steering wheel is
dangerous as it could interfere
with the air bag deployment and
result in serious injury.

Ø

Do not apply the sticker to any
position other than the position
indicated in the illustration of the
speedometer.

10. Switch the ignition ON (engine

running).

11. Turn the compressor on and wait until

the sealant is injected into the tire.
After the sealant is injected into the
tire, continue waiting until the tire is
inflated to the correct air pressure.

NOTE

l

Check the tire inflation pressure label
(driver's door frame) for the correct tire
inflation pressure.

l

If the tire air pressure is not correct after a
few seconds, the tire may be seriously
damaged. Consult an Authorized Mazda
Dealer.

12. When the tire has been inflated to the

proper inflation pressure, turn the
compressor switch off and remove the
hose from the tire valve.

13. Install the tire valve cap.

14. Store the hose, removed from the

valve, in the trunk and resume driving
the vehicle.

CAUTION

Ø

Drive carefully to an Authorized
Mazda Dealer and keep the
vehicle speed below 80 km/h (50
mph).

Ø

If the vehicle is driven over 80
km/h (50 mph), the vehicle might
begin to vibrate.

NOTE

l

If the tire is not properly inflated, the tire
pressure monitoring system warning light
will illuminate (page 4-23).

l

Do not press the tire pressure monitoring
system set switch after installing the spare
tire or after using the emergency flat tire
repair kit. The switch is only to be pressed
after installing the repaired flat tire or
installing a replacement tire (page 4-23).

15. After driving the vehicle 5 km, set up

the compressor again using Step 8 of
the procedure. Turn the compressor
on and then off after a few seconds,
and check the tire air pressure. If the
tire air pressure is low, turn the
compressor on again and wait until
the tire inflates to the correct air
pressure.

CAUTION

Ø

If the tire inflation pressure falls
below 130 kPa (1.3 kgf/cm

2

or bar,

18.9 psi), repair cannot be done
with the repair kit. Park the
vehicle on a level surface off the
right-of-way and contact an
Authorized Mazda Dealer.

Ø

If the tire inflation pressure
continues to remain low, park the
vehicle on a level surface off the
right-of-way and contact an
Authorized Mazda Dealer.

If Trouble Arises

Flat Tire

7-11

Mazda6_8DQ8-EA-13L_Edition3 Page471
Friday, June 13 2014 6:23 PM

Form No.8DQ8-EA-13L

Detailed Information for 2015 Mazda Mazda6 Owners Manual

Lists of information found in 2015 Mazda Mazda6 Owners Manual - Page 471

  • 11. Turn the compressor on and wait until the sealant is injected into the tire.
  • 12. When the tire has been inflated to the proper inflation pressure, turn the compressor switch off and remove the hose from the tire valve.
  • 13. Install the tire valve cap.
  • 14. Store the hose, removed from the valve, in the trunk and resume driving the vehicle.
  • 15. After driving the vehicle 5 km, set up the compressor again using Step 8 of the procedure.
  • 1.3 kgf/cm 2 or bar, 18.

Related Documents for 2015 Mazda Mazda6 Owners Manual