Crown XLS 602 User Manual

Architectural & Engineering Specifi cations

XLS 602 (120 V, 60 Hz models)

XLS 602

background image

Crown International
P.O. Box 1000
Elkhart, IN 46515-1000
TEL: 574-294-8200
FAX: 574-294-8FAX
www.crownaudio.com

XLS 602

03/04                                                          135169-2A  

 

Specifi cations subject to change without prior notice. Latest 
information available at www.crownaudio.com. 
Crown and Crown Audio are registered trademark of 
Crown International. Other trademarks are the property 
of their respective owners.
Printed in U.S.A.

Architectural & Engineering Specifi cations

X L S   S E R I E S

XLS 602 (120 V, 60 Hz models)

The power amplifi er shall be a solid-state two-channel model.

The amplifer shall provide extensive protection and diagnostic capabilities, including 
output current limiting, DC protection, circuit breaker, and special thermal protection 
for the unit’s transformers.

The front-panel controls shall be two black detented level controls (one for each 
channel), a power switch, and a circuit breaker for overload protection.

Front-mounted indicators shall be Clip: one red LED per channel which illuminates 
when the channel’s output signal is being overdriven, Power: one green LED which 
indicates that the amplifi er has been turned on and AC power is available, and Fault: 
one yellow LED which illuminates when amplifi er is in protect mode and briefl y 
during normal power-up when amplifi er is fi rst switched on.

The recommended load impedance shall be 2 to 8 ohms per channel in Stereo and 
8 ohms in Bridge Mono. The amplifi er shall be safe when driving any kind of load, 
including highly reactive ones.

The rear-mounted output connectors shall be two 4-pole Speakon

®

 connectors (one 

per channel) and a pair of 5-way binding posts per channel. Rear-mounted input 
connectors shall be 3-pin balanced XLR connectors.

The power amplifi er shall meet or exceed the following performance criteria: Input 
sensitivity for rated output at 4 ohms: 1.26 V. Rated output with both channels driven 
with 0.15% THD  (at 1 kHz) in Dual mode: 840 watts per channel into 2 ohms, 600 
watts per channel into 4 ohms, and 370 watts per channel into 8 ohms. Rated output 
with 0.5% THD (at 1 kHz) in Bridge-Mono mode: 1,200 watts into 8 ohms and 1,680 
watts into 4 ohms. Frequency Response at 1 watt, 20 Hz to 20 kHz: ±0.75 dB. Phase 
Response at 1 watt: –10 degrees at 10 Hz, +19 degrees at 20 kHz. Signal to Noise 
Ratio below rated power (20 Hz to 20 kHz): greater than 100 dB A-weighted. Total 
Harmonic Distortion at full rated power from 20 Hz to 1 kHz: less than 0.15%. 
Intermodulation Distortion (60 Hz and 7 kHz at 4:1, from full rated output to –40 
dB): less than 0.3%. Damping Factor (8 ohms): greater than 200 from 10 to 400 
Hz. Crosstalk (below rated power, –82 dB at 1 kHz, –58 dB at 20 kHz. Voltage 
Gain at maximum output: 31 dB. Input Impedance (nominal): 20 kilohms balanced, 
10 kilohms unbalanced. AC Line Voltages and Frequencies Available (±10%): 120 
VAC/60Hz and 230 VAC/50 Hz.

The amplifi er chassis shall be constructed of steel with a durable black fi nish and 
shall be designed for fl ow-through ventilation from the front panel to the back 
panel. Internal heat sinks with forced-air cooling shall provide rapid, uniform heat 
dissipation.

The dimensions of the amplifi er shall allow for 19 inch (48.3 cm) EIA standard (RS-
310-B) rack mounting. The amplifi er shall be 3.5 inches (8.9 cm) tall, and 14 inches 
(35.6 cm) deep behind the rack-mounting surface.

The amplifi er shall weigh 27.2 pounds (12.3 kg).

The amplifi er shall be designated the Crown XLS 602

.

1

Detailed Information for Crown XLS 602 User Manual

Lists of information found in Crown XLS 602 User Manual - Page 1

  • 1.26 V.
  • 48.3 cm) EIA standard (RS- 310-B) rack mounting.
  • 3.5 inches (8.
  • 35.6 cm) deep behind the rack-mounting surface.
  • 27.2 pounds (12.

Related Documents for Crown XLS 602 User Manual