Q42885-6 Output Module Parts List (P10305-4 Board); Q42885-6 Output Module (4 Resistor TO-3P Drivers) for- Page 24

Power Base-1 & 460CSL Amplifier Service Manual

24

Q42885-6 Output Module Parts List (P10305-4 Board)

Q42885-6 Output Module (4 Resistor TO-3P Drivers) for

PB-1/460CSL:

CAPACITORS

C01

C 8511-5

.047µF

C02

C 7964-7

.22µF

C03

C 7964-7

.22µF

C04

C 8534-7

.0047µF

C05

C 6807-9

.001µF

C06

C 6806-1

.01µF

C07

C 6807-9

.001µF

C08

C 6810-3

180pF

C09

C 6809-5

220pF

C43

C 6806-1

.01uF

DIODES

D01

C 2851-1

1N4004

D02

C 2851-1

1N4004

D03

C 2851-1

1N4004

D04

C 2851-1

1N4004

D05

C 2851-1

1N4004

D06

C 2851-1

1N4004

D07

C 2851-1

1N4004

D08

C 2851-1

1N4004

D09

C 2851-1

1N4004

D10

C 2851-1

1N4004

D11

C 2851-1

1N4004

D12

C 2851-1

1N4004

INDUCTORS

L00

C 6592-6

Output Coil

L01

C 3510-2

470µH

L02

C 3510-2

470µH

TRANSISTORS

Q17

C 3810-6

NPN MPSA43

Q19

C 3578-9

PNP MPSA93

RESISTORS

R00

A10266-7501

75

R01

A10266-4711

470

R04

D 6600-7

.19 5W

R07

D 6600-7

.19 5W

R10

A10266-4711

470

R11

C 1001-4

2.7 1W

R12

C 3931-0

12 2W

R13

A10266-7501

75

R16

D 6600-7

.19 5W

R19

D 6600-7

.19 5W

R23

C 6844-2

250 Pot LS Bias

R24

A10266-1331

13K

R25

A10266-2221

2.2K

R26

C 6844-2

250 Pot HS Bias

R27

A10266-3911

390

R28

A10266-1331

13K

R29

C 6402-9

51 OHM

R30*

A10265-10201* 102*

R31

C 7778-1

5.6 flame proof

R32

C 7778-1

5.6 flame proof

R33

C 7779-9

22 flame proof

R34

C 7779-9

22 flame proof

R35

C 3931-0

12 2W

R36

C 3931-0

12 2W

R37

C 3931-0

12 2W

R38

C 3931-0

12 2W

R39

C 3931-0

12 2W

R40

C 3931-0

12 2W

MISC.

Board

P10305-4

Jumpers

C 5868-2

0 Ohm Jumper (7)

Clips

D 6414-3

Q17/19 Hold Down

J500

J600

C 7057-0

10 Pos. Connector

BEAD

C 8341-7

Over emitter of Q19

Note: R30 is 102 Ohms in most units, though in some
cases a different value may be used to match the
installed S100/S200 LM334 (C5826-0) device grade.
This is the standard value and is used with the most
common LM334 grade, green. If the LM334 is marked
with a blue dot, R30 should be a 107 Ohm resistor
(A10265-10701); if it is marked with a yellow dot then
R30 should be a 100 Ohm resistor (A10265-10001).