Operation Manual; Important Safety ; CTs Multi-Channel - Page 2

Operation Manual

CTs Multi-Channel 

Power Amplifiers

page 2

1)

Read these instructions.

2)

Keep these instructions.

3)

Heed all warnings.

4)

Follow all instructions.

5)

Do not use this apparatus near water. Do not 
expose to dripping or splashing. Do not place 
objects filled with liquid on unit.

6)

Clean only with a dry cloth.

7)

Do not block any ventilation openings. Install 
in accordance with the manufacturer’s instruc-
tions.

8)

Do not install near any heat sources such as 
radiators, heat registers, stoves, or other 
apparatus that produce heat.

9)

Do not defeat the safety purpose of the polar-
ized or grounding-type plug. A polarized plug 
has two blades with one wider than the other. 
A grounding-type plug has two blades and a 
third grounding prong. The wide blade or the 
third prong is provided for your safety. If the 
provided plug does not fit into your outlet, 
consult an electrician for replacement of the 
obsolete outlet.

10) Protect the power cord from being walked on 

or pinched, particularly at plugs, convenience 
receptacles, and the point where they exit from 
the apparatus.

11) Only use attachments/accessories specified 

by the manufacturer.

12) Use only with a cart, stand, bracket, or table 

specified by the manufacturer, or sold with the 
apparatus. When a cart is used, use caution 
when moving the cart/apparatus combination 
to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms 

or when unused for long periods of time.

14) Refer all servicing to qualified service person-

nel. Servicing is required when the apparatus 
has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has 
been spilled or objects have fallen into the 
apparatus, the apparatus has been exposed to 
rain or moisture, does not operate normally, 
or has been dropped.

15) To reduce the risk of fire or electric shock, do 

not expose this apparatus to rain or moisture.

TO PREVENT ELECTRIC SHOCK DO NOT REMOVE 
TOP OR BOTTOM COVERS. NO USER SERVICE-
ABLE PARTS INSIDE. REFER SERVICING TO 
QUALIFIED SERVICE PERSONNEL. 

À PRÉVENIR LE CHOC ÉLECTRIQUE N’ENLEVEZ 
PAS LES COUVERCLES. IL N’Y A PAS DES PAR-
TIES SERVICEABLE À L’INTÉRIEUR. TOUS REPA-
RATIONS DOIT ETRE FAIRE PAR PERSONNEL 
QUALIFIÉ SEULMENT. 

IMPORTANT

CTs Series amplifiers require Class 2 output 
wiring.

MAGNETIC FIELD

CAUTION! Do not locate sensitive high-gain equip-
ment such as preamplifiers or tape decks directly 
above or below the unit. Because this amplifier has 
a high power density, it has a strong magnetic field 
which can induce hum into unshielded devices that 
are located nearby. The field is strongest just above 
and below the unit.

If an equipment rack is used, we recommend locat-
ing the amplifier(s) in the bottom of the rack and the 
preamplifier or other sensitive equipment at the top.

WATCH FOR THESE SYMBOLS:

The lightning bolt triangle is used to alert the user 
to the risk of electric shock.

The exclamation point triangle is used to alert the 
user to important operating or maintenance instruc-
tions.

Important Safety 
Instructions

FCC COMPLIANCE NOTICE

This device complies with part 15 of the FCC rules. Operation is subject to the following 
two conditions: (1) This device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause undesired 
operation.

CAUTION: Changes or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B 
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses, and can radiate radio frequency energy and, if not installed 
and used in accordance with the instruction manual, may cause harmful interference to 
radio communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the    

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.