Rear Panel; Power Voltage Switch: ; Output Connectors: - Page 2

Crown International

1718 W. Mishawaka Rd.

Elkhart, IN 46517-9439

TEL: 574-294-8200

FAX: 574-294-8FAX

www.crownaudio.com

05/13  

The symbols shown above are internationally accepted 

symbols that warn of potential hazards with electrical 

products. The lightning flash with arrowpoint in an 

equilateral triangle means that there are dangerous volt-

ages present within the unit. The exclamation point in an 

equilateral triangle indicates that it is necessary for the 

user to refer to the owner’s manual.

These symbols warn that there are no user serviceable 

parts inside the unit. Do not open the unit. Do not attempt 

to service the unit yourself. Refer all servicing to qualified 

personnel. Opening the chassis for any reason will void 

the manufacturer’s warranty. Do not get the unit wet. If 

liquid is spilled on the unit, shut it off immediately and 

take it to a dealer for service.  Disconnect the unit during 

storms to prevent damage.

Rear Panel

Specifications subject to change without prior notice. Latest information 

available at www.crownaudio.com.

Crown and Crown Audio are registered trademarks of Crown International. 

Other trademarks are the property of their respective owners. 

©2013 Crown Audio

®

, Inc. Printed in China

Crown’s Three-Year, No-Fault, Fully Transferable 

Warranty

Crown offers a Three-Year, No-Fault, Fully Transferable War-

ranty for every new Crown amplifier—an unsurpassed indus-

try standard. With this unprecedented No-Fault protection, 

your new Crown amplifier is warranted to meet or exceed 

original specifications for the first three years of ownership. 

During this time, if your amplifier fails, or does not perform 

to original specifications, it will be repaired or replaced at our 

expense. About the only things not covered by this warranty 

are those losses normally covered by insurance and those 

caused by intentional abuse. And the coverage is transferable, 

should you sell your amplifier. See your authorized Crown 

dealer for full warranty disclosure and details. 
For customers outside of the USA, please contact your au-

thorized Crown distributor for warranty information or call 

574-294-8200.

CXM2000

AC Power Inlet: 

Connects to 100V~120V or 

220V~240V, 50Hz/60Hz AC power supply.

Power Voltage Switch: 

Select the power supply 

voltage to be 100V~120V or 220V~240V.

USB Connector: 

Connects for firmware update 

only. 

8-way DIP Switches: 

Switches 1~4 are for JBL 

cinema speaker selection. Switch 5 is for fault 

detection. Switch 6 is for 5.1 or 7.1 channel instal-

lation system selection. Switches 7 and 8 are for 

monitor and fault detection functions of subwoofer 

1 and 2.

Output Connectors: 

Connects the HD-15 connec-

tors to the Crown DSi series or XLC series ampli-

fiers through VGA cables. This allows the CXM2000 

to send and receive signals from the amplifiers for 

fault detection and monitor function. 

L-Bi-amp:

 Connects to the amplifier of left channel 

(bi-amp speaker) or left and right channels (passive 

speaker).

R-Bi-amp:

 Connects to the amplifier of right chan-

nel (bi-amp speaker).

C:

 Connects to the amplifier of center channel.

SW1:

 Connects to the amplifier of low frequency 

effect channel (subwoofer 1). 

SW2:

 Connects to the amplifier of low frequency 

effect channel (subwoofer 2).

Ls/Rs: 

Connects to the amplifier of left surround & 

right surround channels.

Bsl/Bsr:

 Connects to the amplifier of back sur-

round left & back surround right channels.

Input Connector: 

Connects the HD-25 connector 

to the main outputs of the cinema processor. 

RS232 Connectors: 

Connects the RS232 con-

nector to the Theater Management System (TMS)  

for sending fault detection results. 

Rear Panel Connectors

Power Consumption

100V ~120V /  220V ~ 240V, 50Hz / 60 
Hz, 50W

Processor Input Channels:

8 inputs (Left, Center, Right, Surround 
Left, Surround Right, Back Surround 
Left, Back Surround Right, Subwoofer).

Input Impedance 
(Processor Inputs)

>10k 

Ω

Input Impedance (Power 
Amplifier Inputs)

>10k 

Ω

Signal to Noise Ratio

104 dB (A weighted)

Crosstalk

> 80 dB (A weighted)

Internal Monitor Speaker 
Power

8W

DSP Section

DSP only for Left, Right and Center 
channel speakers

Input EQ

High and low shelving filters

Output EQ

8 parametric filters per channel

Delay

Up to 10 msec total delay per channel

Presets

11 presets. One is “ bypass”. Ten are 
factory-set for JBL cinema systems.

Operating Temperature

32°F to 104°F (0°C to 40 °C) 95% 
relative humidity (non-condensing)  

Dimension 
(L x D x H)

18.97” X 8.26” X 3.46” 
(482 mm X 210 mm X 88 mm)

Net Weight

10.47 lbs (4.75 Kg)

Net Shipping Weight

13.34 lbs (6.05 Kg)