1 Warning
All rights reserved under International
and Pan American copyright conventions
Copyright 2014 Crown Equipment Corp.
It’s the law, you must be trained and certifi ed to operate this truck.
(OSHA § 1910.178, Rev. 1999)
You or others around you can be seriously injured or even killed if
you don't use this truck correctly.
Read and obey all warnings and instructions in this Manual* and
on the truck.
Head, arms, hands, legs or feet outside the operator area can be
pinned or crushed whenever the truck is moving. Stay within the
operator area and
stop the truck completely before getting off .
A dockboard can move or drop while you are on it. Or you could
drive off a dock. Falls from docks or dockboards can cause
serious injury or even death.
You can be trapped or crushed by objects protruding or poking
into the operator area.
Look where you are going.
Inspect your truck before starting work, make sure it is in good
working order.
* Additional copies of this Operator Manual and all Truck Labels can be obtained
from Crown Equipment Corporation, New Bremen, Ohio 45869 U.S.A
.
Left Header
Protect 0
Warning Labels
Warning Labels 42
EACH WARNING LABEL
ON YOUR TRUCK IS IMPORTANT
Read and obey all of them to protect
yourself and others.
All rights reserved under International
and Pan American copyright conventions
Copyright 2014 Crown Equipment Corp.
Batteries produce explosive gas.
Do not
smoke, use open fl ame or create an arc or
sparks near this battery. Ventilate well in
enclosed areas and when charging.
Batteries contain
Sulfuric Acid
which
causes severe burns. Do not get in eyes, on
skin, or clothing. In case of contact, fl ush
immediately and thoroughly with water. Get
medical attention if your eyes are affected.
20
DANGER
Tilting mast forward when forks
are raised and loaded can tip the
truck over causing injury or death.
Do not tilt elevated load forward
unless it is over a stack.
WARNING
Lifting people without
a proper platform
could cause a fall or
other serious injury.
Platform must be built
and used as specifi ed
in OSHA 1910.178
and ANSI-B56.1.
WARNING
Stay clear of all
moving parts.
Moving parts can
cut or crush hands,
feet, arms or legs.
WARNING
You can tip this truck over
if you turn too sharply for the
conditions around you. Don't risk
injury or death.
Slow down when turning.
Buckle seatbelt
WARNING
WARNING
It's the law,
you must be
trained and
certifi ed to
operate this
truck.
(OSHA § 1910.178, Rev. 1999)
You or people around you
could be seriously injured
or even killed if you don't
use this truck correctly.
Obey all instructions &
warnings in the operator
manual and on the truck.
Avoid being
crushed.
Keep
head, arms,
hands, legs, and
feet within the
operator area.
Stop truck completely
before getting off.
Falls from
docks can
cause serious
injury or even
death.
Keep seatbelt
fastened, hold on, and
brace your feet in these
emergencies.
You could
be pinned
or crushed
by objects
intruding or
poking into the operator
area.
Look where you
are going.
Inspect your truck before
starting work, make sure
it's in good working order.
* Additional copies of the
Operators Manual and Truck
Labels can be obtained from:
Crown Equipment Corp.,
crown.com
WARNING
Falling objects or lowering
forks can cause serious injury
or death.
Never stand under the forks.
While servicing, block the
forks so they won't fall.
DANGER
In case of
tip-over
Follow
these
instructions:
Lean
away
from tip
Don't Jump!
Hold on tight
Brace feet
8280-A
WARNING
Similar looking
trucks can have a
different stopping
distance.
Know the distance it
takes to stop before
you start working.
WARNING
Passengers could
be seriously injured.
There is no safe
place for them
to ride.
No Passengers.
WARNING
Standing or riding on the
forks can cause a fall.
You can be seriously
injured or killed.
Never stand or ride on
forks for any reason.
8284-A
WARNING
Remove and discard this label after the truck
has been delivered to the customer.
This SC5200 unit’s maximum travel speed is set
at 9.5 mph.
Similar looking trucks may have the maximum
travel speed set differently.
All SC5200 units at the customer location should
be set to the same maximum travel speed.
Refer to PF26301 for instructions.