Blue: Neutral; Brown: Live; FDA Regulations (100 to 120 volt Model Only)- Page 5

3

FDA Regulations (100 to 120 volt Model Only)

U.S. Food and Drug Administration (FDA) has implemented regulations for 
laser products manufactured on and after August 2, 1976. Compliance is 
mandatory for products marketed in the United States. One of the following 
labels on the back of the printer indicates compliance with the FDA 
regulations and must be attached to laser products marketed in the United 
States.

☛

 Caution:

Use of controls, adjustments or performance of 
procedures other than those specified in this manual may 
result in hazardous radiation exposure. 

IEC 60825 specification (220 to 240 volt model only)

This printer is a Class 1 laser product as defined in IEC 60825 specifications. 
The label shown below is attached in countries where it is needed.

This printer has a Class 3B laser diode which produces invisible laser 
radiation in the scanner unit. You should not open the scanner unit under any 
circumstances. 

☛

 Caution:

Use of controls or adjustments or performance of 
procedures other than those specified herein may result in 
hazardous radiation exposure.

For Finland and Sweden
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT

☛

 Varoitus! 

Laitteen käyttäminen muulla kuin tässä käyttöohjeessa 
mainitulla tavalla saattaa altistaa käyttäjän 
turvallisuusluokan 1 ylittävälle näkymättömälle 
lasersäteilylle. 

☛

 Varning 

Om apparaten används på annat sätt än i denna 
Bruksanvisning specificerats, kan användaren utsättas för 
osynlig laserstrålning, som överskrider gränsen för 
laserklass 1.

Internal laser radiation

Maximum radiation power: 5 mW
Wave length:

760 - 810 nm

Laser class:

Class IIIb 
(Accordance with 21 CFR Part 1040.10)
Class 3B 
(Accordance with IEC 60825)

IMPORTANT - For Your Safety

To ensure safe operation the supplied three-pin plug must be inserted only 
into a standard three-pin power outlet that is properly grounded through the 
normal household wiring. 

Extension cords used with this printer must be three-pin plug type and 
correctly wired to provide proper grounding. Incorrectly wired extension 
cords may cause personal injury and equipment damage. 

The fact that the equipment operates satisfactorily does not imply that the 
power is grounded and that the installation is completely safe. For your 
safety, if in any doubt about the effective grounding of the power, call a 
qualified electrician. 

Disconnect device

You must install this printer near a power outlet that is easily accessible. In 
case of an emergency, you must disconnect the power cord from the power 
outlet to shut off the power completely.

Caution for LAN connection

Connect this product to a LAN connection that is not subjected to over 
voltages.

IT power system (For Norway only)

This product is also designed for an IT power system with phase-to-phase 
voltage 230V.

Geräuschemission / Acoustic noise emission (for Germany 
only)

Lpa < 70 dB (A) DIN 45635-19-01-KL2

Wiring information (for UK)
Important

If you need to replace the plug fuse, fit a fuse that is approved by ASTA to 
BS1362 with the same rating as the original fuse.

Always replace the fuse cover. Never use a plug that does not have a cover.

Warning - This printer must be earthed.

The wires in the mains lead are coloured in line with the following code :

Green and Yellow: 

Earth

Blue: Neutral
Brown: Live

If in any doubt, call a qualified electrician.

MANUFACTURED:
Brother Industries, Ltd., 
15-1 Naeshiro-cho Mizuho-ku Nagoya, 467-8561 Japan
This product complies with FDA radiation performance standards, 21 
CFR subchapter J.

MANUFACTURED:
Brother Technology (Shenzhen) Ltd.
NO6 Gold Garden Ind. Nanling Buji, Longgang, Shenzhen, China
This product complies with FDA radiation performance standards, 21 
CFR Subchapter J

CLASS 1LASERP RODUCT
APPAREIL Å LASER DE CLASSE 1
LASER KLASSE 1 PRODUKT