Safety Precautions; Maschinenlärminformations- Verordnung 3. ; IEC 60825-1 specification (220 to 240 volt model - Page 8

Safety Precautions

6

IEC 60825-1 specification (220 to 240 volt model 

only)

This printer is a Class 1 laser product as defined in 
IEC 60825-1+A2: 2001 specifications. The label 
shown below is attached in countries where it is 
needed.

This printer has a Class 3B laser diode which 
produces invisible laser radiation in the laser unit. You 
should not open the laser unit under any 
circumstances. 

Caution

Use of controls or adjustments or performance of 
procedures other than those specified herein may 
result in hazardous radiation exposure.

For Finland and Sweden

LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT

Varoitus!

Laitteen käyttäminen muulla kuin tässä 
käyttöohjeessa mainitulla tavalla saattaa altistaa 
käyttäjän turvallisuusluokan 1 ylittävälle 
näkymättömälle lasersäteilylle.

Varning

Om apparaten används på annat sätt än i denna 
Bruksanvisning specificerats, kan användaren 
utsättas för osynlig laserstrålning, som överskrider 
gränsen för laserklass 1.

Internal laser radiation

IMPORTANT - For Your Safety

To ensure safe operation, the supplied three-pin plug 
must be inserted only into a standard three-pin power 
outlet that is properly grounded through the normal 
household wiring. 
Extension cords used with this printer must be three-
pin plug type and correctly wired to provide proper 
grounding. Incorrectly wired extension cords may 
cause personal injury and equipment damage. 
The fact that the equipment operates satisfactorily 
does not imply that the power is grounded and that 
the installation is completely safe. For your safety, if 
in any doubt about the effective grounding of the 
power, call a qualified electrician. 
This product should be connected to an AC power 
source within the range indicated on the rating label. 
DO NOT connect it to a DC power source. If you are 
not sure, contact a qualified electrician.

Maschinenlärminformations- Verordnung 3. 

GPSGV (For Germany only)

Der höchste Schalldruckpegel beträgt 70 dB(A) oder 
weniger gemäß EN ISO 7779.

Disconnect device

You must install this printer near a power outlet that is 
easily accessible. In case of an emergency, you must 
disconnect the power cord from the power outlet to 
shut off the power completely.

Caution for LAN connection

Connect this product to a LAN connection that is not 
subjected to over voltages.

IT power system (For Norway only)

This product is also designed for an IT power system 
with phase-to-phase voltage 230V.

Wiring information (for UK)

Important

If you need to replace the plug fuse, fit a fuse that is 
approved by ASTA to BS1362 with the same rating as 
the original fuse.
Always replace the fuse cover. Never use a plug that 
does not have a cover.

Warning - This printer must be earthed.

The wires in the mains lead are coloured in line with 
the following code:

If in any doubt, call a qualified electrician.

Wi-Fi Alliance certification

This wireless Ethernet multi-function print server is a 
Wi-Fi certified IEEE 802.11b/802.11g product by the 
Wi-Fi Alliance. For more information on the Wi-Fi 
Alliance and other Wi-Fi certified products, visit 
http://www.wi-fi.org.

Maximum radiation power:

10 mW

Wave length:

780 - 800 nm

Laser class:

Class 3B

CLASS 1 LASER PRODUCT
APPAREIL À LASER DE CLASSE 1
LASER KLASSE 1 PRODUKT

Green and Yellow: Earth
Blue:

Neutral

Brown:

Live