䴀攀挀栀愀渀椀挀愀氀 瀀爀漀戀氀攀洀猀; 1. Fabric is not fed properly; 2. Needle breaks- Page 134
Brother PC-6500 User's Guide
Table of Contents
Symptom
1. Fabric is not fed properly
2. Needle breaks
3. Machine is noisy, or running at a slow
speed, or thread trimming is not good
4. Machine does not start
5. Embroidery unit does not work
Remedy
1. Raise feed dogs.
2. Attach correct presser foot.
3. Install correct needle.
4. Remove thread ends from race or
inner shuttle.
1. Insert needle correctly.
2. Install proper needle.
3. Check “FABRIC/THREAD/NEEDLE
COMBINATIONS” chart on page 19.
4. Sew without pulling fabric; just guide it.
1. Remove dust by cleaning with a brush.
1. Press start/stop button.
2. Set main power switch to “ I ”.
3. Lower presser foot lever.
4. Refer to “ERROR MESSAGES” on
1. Set main power switch to “ I ”.
2. Correctly attach embroidery unit to
sewing machine.
3. Turn off machine, then insert memory
card.
4. Refer to “ERROR MESSAGES” on
5. Refer to “Initializing the embroidery
Probable cause
1. Feed dogs are lowered.
2. Combination of selected stitch and
presser foot is not correct.
3. Correct needle is not being used.
4. Thread is entangled.
1. Needle is not correctly inserted.
2. Correct needle is not used.
3. Combination of fabric, thread and
needle is not correct.
4. Fabric is pulled too much.
1. Dust is clinging to bottom of needle
plate.
1. Start/stop button is not pressed.
2. Machine is turned off.
3. Presser foot is not lowered.
4. Check for error messages on LCD.
1. Machine is turned off.
2. Embroidery unit is not correctly
attached.
3. Memory card is not inserted.
4. Check for error messages on LCD.
5. Embroidery unit was not correctly
initialized.
Mechanical problems
131
Detailed Information for Brother PC-6500 User's Guide
Lists of information found in Brother PC-6500 User's Guide - Page 134
- 1. Fabric is not fed properly 2.
- 3. Machine is noisy, or running at a slow speed, or thread trimming is not good 4.
- 5. Embroidery unit does not work Remedy 1.
- 2. Attach correct presser foot.
- 3. Install correct needle.
- 4. Remove thread ends from race or inner shuttle.
- 1. Insert needle correctly.
- 2. Install proper needle.
- 3. Check “FABRIC/THREAD/NEEDLE COMBINATIONS” chart on page 19.
- 4. Sew without pulling fabric; just guide it.
- 1. Remove dust by cleaning with a brush.
- 1. Press start/stop button.
- 2. Set main power switch to “ I ”.
- 3. Lower presser foot lever.
- 4. Refer to “ERROR MESSAGES” on page 125.
- 1. Set main power switch to “ I ”.
- 2. Correctly attach embroidery unit to sewing machine.
- 3. Turn off machine, then insert memory card.
- 4. Refer to “ERROR MESSAGES” on page 125.
- 5. Refer to “Initializing the embroidery unit” on page 87.
- 1. Feed dogs are lowered.
- 2. Combination of selected stitch and presser foot is not correct.
- 3. Correct needle is not being used.
- 4. Thread is entangled.
- 1. Needle is not correctly inserted.
- 2. Correct needle is not used.
- 3. Combination of fabric, thread and needle is not correct.
- 4. Fabric is pulled too much.
- 1. Dust is clinging to bottom of needle plate.
- 1. Start/stop button is not pressed.
- 2. Machine is turned off.
- 3. Presser foot is not lowered.
- 4. Check for error messages on LCD.
- 1. Machine is turned off.
- 2. Embroidery unit is not correctly attached.
- 3. Memory card is not inserted.
- 4. Check for error messages on LCD.
- 5. Embroidery unit was not correctly initialized.
Related Documents for Brother PC-6500 User's Guide
All trademarks are property of their respective owners. Tightrope
Interactive